Code of practice for the application of bitumen mastic for waterproofing of roofs
1967 الطبعة

Per IS 4365, suitable substrates for bitumen mastic include:

• Horizontal and gently sloping surfaces that are smooth, even, and free from irregularities (Clause 4.3.1).
• Vertical or steep timber slopes exceeding 30°, where an isolating membrane is mandatory between the timber and bitumen mastic to prevent adhesion problems (Clause 4.4.1). This membrane should be affixed using galvanized nails conforming to IS 723.
• Surfaces must be clean and thoroughly prepared to bond effectively with blown or residual bitumen (Clause 2.2).

Key considerations:

• The substrate surface should be uniform and crack-free.
• Timber surfaces require an isolating membrane.
• Appropriate bonding bitumen selection depends on local temperature and slope.

جارٍ تحميل المخطط…

This approach ensures proper adhesion and durability of the bitumen mastic waterproofing layer.

IS 4365 recommends the following for installing isolating membranes on timber roofs:

• Use a hessian-based type 3 felt as specified in IS 1322-1965.
• The membrane must be securely nailed to the timber surface.
• Galvanized round-headed nails as per IS 723 with an 11 mm diameter and 20 mm length should be used.
• Nails should be spaced no more than 150 mm apart.
• Overlaps must be at least 100 mm at the ends and 75 mm along the sides.
• This membrane installation is compulsory for roofs with slopes over 30° between timber and bitumen mastic.
• Timber boards should be well-seasoned, minimum 25 mm thick, tongued and grooved or tightly butted, rigid, and dry before membrane application.
• Adequate ventilation between the roof deck and ceiling must be provided to prevent fungal growth.

Summary Table:

جارٍ تحميل المخطط…

This installation safeguards against moisture ingress, prevents direct timber-bitumen contact, and extends roof lifespan.

According to IS 4365, the recommended bitumen mastic thickness and number of coats vary based on roof slope as follows:

• For horizontal roofs such as terraces or balconies subjected to foot traffic:

  • Apply two coats:
    • First coat minimum thickness: 10 mm
    • Second coat minimum thickness: 15 mm

• For slopes exceeding 30° and vertical surfaces (excluding timber):

  • Either two coats with a total thickness of at least 13 mm
  • Or three coats with a total thickness of at least 20 mm

• For flat surfaces and gentle slopes:

  • Apply bitumen mastic evenly ensuring the base has a slope of at least 1 in 60 to facilitate drainage

Thickness per coat depends on the maximum practical thickness achievable while the mastic remains warm and plastic (refer Clauses 4.8.1 to 4.8.5).

جارٍ تحميل المخطط…

This ensures proper waterproofing durability and efficient drainage.

IS 4365 outlines the following procedure for remelting and handling bitumen mastic on-site:

• Utilize a mechanical mixer suitable for the site conditions and roof area.
• Break bitumen mastic blocks (conforming to IS 3037-1965) into pieces and arrange them in layers around the mixer's edges proceeding towards the center.
• Gradually heat the mastic to approximately 200°C, ensuring the temperature does not exceed this limit to prevent deterioration.
• Continuously stir the mixture for uniform consistency.
• Add coarse aggregates only after the bitumen has fully melted, mixing thoroughly until evenly dispersed.
• Transport the molten mastic in small batches using buckets coated with fine inert dust (excluding ash or oil) to avoid contamination and sticking.
• Position the mixer close to the application area to minimize cooling during transfer.

This method maintains the bitumen mastic’s workability and performance on the roof.

جارٍ تحميل المخطط…

To boost durability and decrease solar heat absorption on bitumen mastic roofs, IS 4365 recommends:

• Spreading light-colored mineral aggregates or pea-sized gravel uniformly over the warm bitumen surface, bonded with bituminous material to increase solar reflectivity.
• Installing cement concrete flooring tiles (as per IS 1237-1959) over bitumen mastic primed with bitumen primer (IS 3384-1965), suitable for roofs experiencing continuous foot traffic. Tiles must be fixed using hot bituminous bonding with carefully sealed joints and edges.
• Applying decorative finishes such as aluminium paint or coloured bitumen emulsion paint compatible with bitumen mastic.
• Preparing the surface by rubbing warm bitumen with clean sharp sand sized between 300 and 850 microns using a wooden float to create texture and keying.

These finishes improve weather resistance, durability, and thermal comfort by reducing heat gain.

جارٍ تحميل المخطط…

Key dimensions to note:

• Tile joints should be approximately 25 mm wide.
• Space at wall upstands should be around 75 mm.
• Sand particle size for rubbing ranges from 300 to 850 microns.

This ensures a long-lasting, reflective, and serviceable roof finish in line with IS 4365.